Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
Do you find yourself trying to locate help and advice concerning How to Install a Bathtub?
Installing a tub isn't exactly brain surgery, however it does require solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a moderately difficult task. If the old tub is conveniently accessible, the task can move immediately; if you have to open a wall to get rid of the old tub and place the new bath tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need an assistant to leave the old tub and also embeded in the new one. Ensure you have certified yourself for the job and are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed project, it is far better to consider employing one before you begin. Chances are you might need an expert plumber to make tube links.
This post will aid you set up a brand-new bathtub in your washroom if you have actually currently purchased a brand-new bathtub and don't require to alter the setup of your previous water system pipes.
Your tools and also material checklist need to make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be quite problematic due to the restricted accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the staying water that will come from the pipes. As soon as the supply pipelines have been removed, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before moving on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making sure that the washers remain in place between the tap and also the sink. Safeguard the tap in position with the supplier offered backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap connectors. The previous type ought to be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Using both wooden boards under its feet, place the tub in the required setting. The wood boards are valuable in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the tub till the level checks out degree.
To mount taps, fit all-time low of the furthest adaptable faucet port to the proper supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water and also examine all joints and new pipework for leakages as well as tighten them if necessary. Fill up the tub as well as additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, repair the bath paneling as defined in the maker's user's manual. Tiling as well as sealing around the bath tub ought to wait till the bath tub has been utilized at least when as this will certainly settle it into its last position.
Preparing for the Installation
First of all, the supporting framework supplied with the bathroom ought to be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to avoid stress on the bathtub.
Fit the flexible faucet connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final position.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a stiff seal, triggering the water to pass through the wall in between the bathroom and the tiling, bring about problems with moisture and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes and cartridges, and are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to allow for the movement experienced when the tub remains in usage. The sealer can split fairly early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly offered on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our section about How to Install a Bathtub. Thanks so much for spending some time to read our blog. Do you know anybody else who is occupied with the niche? Please feel free to promote it. Thank you for your time invested reading it.
Need assistance? Call. Report this page